And.... there it sits...

Alright folks... how are you all???

Right, been a bit busy recently... i could give you a list of excuses but basically... i dont have to explain myself to you lot :p :p :p :p

First up, started a new engine mount, but i'll show you more of that when i get the rest finished....






Dragged the gearbox outside for some TLC in the sun and various bits of the engine got plated/anodised/vapour blasted....








So we had them bits... and an empty engine bay....





I think you can tell the next stage.....

trothles 4pap 45/50mm?

a vu d’œil je dirais 45mm

hâte de l'entendre celle-ci

Apologies for the lack of updates...

Photobucket has ruined my blog which is upsetting... I've been enjoying summer with the family but have done a few bits and pieces..

Still learning Flickr so bare with me....

https://www.flickr.com/photos/156772598 ... res/973710

Damned Photobucket

thanks for the links

Hi there...

Apologies... things have been busy with life.. moving + renovating home.. my family.. Work..

I have still been chipping away with this though..


Had some custom hoses made up from Samco..

https://i.imgur.com/RyUDcrY.jpg

https://i.imgur.com/v9KIgRZ.jpg


Bought a 'proper' bonnet and fitted aero catches.. I also had to trim out some of the ribs for clearance..

https://i.imgur.com/kWxLRVY.jpg

https://i.imgur.com/mbtBkPD.jpg

https://i.imgur.com/8cs90za.jpg

https://i.imgur.com/GlYRsKR.jpg

Lovely paint!!!

https://i.imgur.com/3Bgk7VE.jpg

Also made a tank cover with some cool 1/4 turn fixings..

https://i.imgur.com/GmjS50m.jpg

And after a bit of setting up on the laptop...

This happened..

https://i.imgur.com/1n0ksKv.gifv

https://i.imgur.com/VMgLLJg.gifv


Apologies for the lack of updates on forums..

I find most stuff just gets thrown straight onto instagram these days...

I'm on there as..

SLAMMED106

Hope you guys+girls are all good ...

the project is ready/close the finish

Yes very close... I need to bleed the brakes and it needs final mapping.. oh, and the bodykit refitting after the paint has been polished...

Hey there peeps..

Apologies for the lack of updates on here, maybe it's the fact my only internet access is through a phone so typing long form like this is a bit of a ballache.. photobucket going mental didn't help.. maybe I'm just a lazy twat and that's why 90% of stuff gets fired straight onto Instagram...

However, Iet's try a quick catch up..

Lots of little odds and ends being done now tbh...

First up:


Aerial blanking dooberry-



And just for all you part number geeks-





However, this simple job became a bit of a.... fucking ballache!!! Some doofus has gone and put a cage right over the access hole inside!!-




Next up, arch mouldings- being a bit of a hoarder I've amassed quite a few of these so the best of each section was dug out, scrubbed with hot soapy water, dried, scrubbed with a diluted isopropynol mix, dried, then Gtechniq C4 applied.. got to say this stuff is bloody good..

By now your thinking "Well this jobs sailing along" however.. despite me having 3 drivers side rear arch mouldings all of them had some pins broken off, oh, and Peugeot no longer supply the correct fitting kit...

So after a few phone calls I repeatedly got told 'It's polypropylene mate, can't do anything with that' I had a Google, had an eBay, and bought some of this-




To fix these-




Very impressed, it dries quick and seems to be bloody tough..

Next up, fitting kit!!

Got myself some 20mm diameter rubber washers with a 6mm hole and some stainless 6mm starlocks-









And it seems to be a victory!!








And that's about where I am.at the minute...

Borrowed a torque wrench to do the hideously tight 307 hub nuts up... need to sort a new battery... then I guess it's off to the mappers...


Stu

Well done, almost the end!

Hello Davenport